Home / Tutorials
Tutorials · Resin printing
3D printing tutorials
Resin can be nasty stuff, but it prints the detail taxidermy pieces need. Here's the short version of how to print it safely, a few tips for the Anycubic Photon Mono M7 Pro, and how a water-wash resin workflow goes from vat to finished part.
Resin printing basics
The short version
This is the quick tour. For settings basics, resin types and the mistakes I see most, read Resin printing 101.
Safety and PPE
- Gloves every time. Wear nitrile gloves whenever you touch liquid resin, a wet print, the vat or the build plate. I recommend thick 10 mil nitrile gloves. Swap them if they tear or get soaked.
- Protect your eyes. Wear safety glasses or goggles when pouring, scraping or washing. Anycubic's resin instructions call for gloves and goggles.
- Keep it off your skin. If you get resin on your skin, wash it off with soap and water right away. Don't use alcohol on your skin.
- Keep it away from kids, pets and food. Print somewhere they can't get to, and never use kitchen tools for resin.
Note: Always follow your resin's safety data sheet (SDS). It is the final word on PPE, first aid and disposal for that bottle.
Ventilation
Print in a well-ventilated room, not a closed bedroom or living area. Even "low odor" resin gives off fumes. A window fan pulling air out, or an enclosure vented outside, makes a real difference. Keep the printer out of direct sunlight, because sunlight cures resin in the vat.
Exposure and layers
Resin printers cure each layer with UV light from the screen. The settings that matter most:
- Layer height: thinner layers give finer detail and take longer.
- Normal exposure: how long each layer is cured. Too short and fine details fail. Too long and the details blur and holes close up.
- Bottom layers and bottom exposure: the first few layers cure much longer so the print sticks to the build plate.
Exposure changes with every resin, color and printer, and even with room temperature. Start from the resin maker's recommended exposure for your printer, then run an exposure calibration print and adjust from there. Don't copy numbers from someone else's machine and expect them to work.
Supports and orientation
- Angle it. Tilting a part (often somewhere around 30–45°) spreads the peel force over smaller layers than printing it flat.
- Hollow and drain. Big solid parts waste resin and can crack. If you hollow a part, add drain holes so trapped resin can get out and the vat doesn't create suction.
- Supports where it counts. Every overhang and "island" (a part of a layer that starts in mid-air) needs support. Keep supports on the side that won't show, so the marks end up on the back of a skull or the underside of a head.
- Check in the slicer. Run your slicer's island or support check before every print.
Cleaning and curing
- Wash off uncured resin: alcohol for standard resin, water for water-washable.
- Remove supports with gloves and eye protection on.
- Dry the part completely.
- Post-cure under UV until it's no longer tacky. Don't overdo it.
More detail is in Resin printing 101.
Anycubic Photon Mono M7 Pro tips
General tips for this printer
The Photon Mono M7 Pro is the resin printer I recommend for taxidermists printing duck heads. These are general tips for that printer, based on what Anycubic publishes. Your manual is still the final word.
What you're working with
- Build volume: 223 × 126 × 230 mm, according to Anycubic.
- Screen: a 10.1-inch 14K monochrome LCD with 16.8 × 24.8 µm XY resolution.
- Layer height range: 0.01–0.15 mm.
- Leveling-free: Anycubic lists it as leveling-free. It senses pressure between the platform and the screen before it starts printing.
- Heated vat: the vat's temperature control is adjustable from 20–40 °C, and the default is 25 °C.
- Automatic resin refill and withdrawal, plus resin-level detection, failed-print detection, resin-residue detection and a release-film lifespan reminder.
- No power-loss resume. Anycubic lists it as not supported, so a power outage ends the print.
Tips
- Use the heater in a cold shop. Anycubic's manual says printing below 20 °C can cause bottoms to detach or parts to go missing, and suggests turning on pre-print heating. With it on, printing starts once the resin reaches 25 °C. Don't touch the vat bare-handed after a long heat-up, because it gets hot.
- Leave a little extra resin. The resin-level check wants about 100 ml more than the model needs, because resin clings to the vat and the plate.
- Mind the viscosity limits. Anycubic lists the auto-refill as working with resins up to 7000 cps and the heater with resins up to 9000 cps. Check your resin's data sheet if it's a thick one.
- Flush the feed line when you change resin. To avoid mixing colors, or before clear resin, Anycubic suggests running alcohol from an empty bottle through the auto-feed/discharge function.
- Don't let resin sit. When you're done for the day, send the resin back to the bottle with the auto-withdrawal or a filter funnel, so pigment doesn't settle in the vat.
- Prints not sticking? Clean the build plate with alcohol, then raise the bottom exposure and bottom layer count in small steps.
- Resin splashing or suction cups? Hollow parts need drain holes to break the vacuum. Anycubic's FAQ recommends the same thing.
- File format: it reads
.pwszslice files. Anycubic recommends a FAT32 USB drive of 32 GB or less, with simple file names. Wi-Fi and LAN are also supported. - Air purifier or the auto-refill, one at a time. They share a single USB power port, so they can't run at the same time.
Settings: Anycubic publishes recommended settings for each of its resins on that resin's product page. Start with those, then run a calibration print. How to dial them in is in Resin printing 101.
Water-wash resin workflow
From vat to finished part
Water-washable resin cleans up with water instead of alcohol. It's the resin I recommend for duck heads, but it still needs the same gloves and care as any resin.
- Shake the bottle well, then print with the resin maker's settings for your printer.
- Wash in clean water, like in the Wash & Cure 3 Plus I mention in the FAQ, for the time on the data sheet.
- Dry it completely. Anycubic notes this helps prevent water absorption and cracking.
- Post-cure under UV for the listed time.
- Never pour rinse water down the drain. It's full of uncured resin. Cure it in sunlight, filter out the solids, and dispose of them per local rules.
Note: Always follow your resin's safety data sheet.
Ready for a custom piece?
Send me photos
Every antler is different, so every quote is custom. Send photos through a request form and I'll get back to you.
Dan the 3D Man