Home / FDM printing guide
Guides · FDM printing
FDM printing guide
How to set up 3D model files for filament (FDM) printers, with a focus on big pieces like skull replicas: slicing, orientation, supports, strength settings, bed adhesion, splitting large models and choosing a filament.
Slicing basics
Set it up before you hit print
The numbers on this page are typical starting points that most slicers and filament makers land near. Your filament's label and your printer's profile come first.
- Start from a good profile. Use your slicer's built-in profile for your printer and filament, then change one thing at a time.
- Check the scale and units. A model exported in the wrong units can come in at a tenth or ten times the size. Measure it in the slicer before you slice.
- Preview every layer. Scrub through the layer preview for gaps, floating sections and supports in the wrong spots.
- Print a small test first. A scaled-down copy or a cut section shows fit and detail problems before you burn a day and a spool on the full piece.
Orientation
The biggest single choice
- Put the best face up or toward the side, not down on supports. On a skull that usually means the front and the nasal area stay off the support side.
- Use a big flat area on the bed for stability and adhesion when the model has one.
- Think about strength. FDM parts are weakest between layers. Orient thin, load-bearing features like antler pegs or mounting tabs so the layers run along their length, not across them.
- Fewer overhangs means fewer supports and less cleanup. Overhangs up to about 45° usually print without support.
Supports and tree supports
Hold up what needs holding
- Normal (grid) supports are sturdy and simple, but they touch a lot of surface and leave more marks.
- Tree supports branch up from fewer contact points. They work well on organic shapes like skulls, antlers and heads, use less material and are usually easier to remove.
- Block supports where you don't need them, such as inside cavities you won't see, using support blockers or painting supports on in your slicer.
- Interface layers and a small Z gap make supports peel off cleaner. Adjust them in small steps.
Walls, infill and layer height
Strength vs time
- Walls (perimeters) do most of the work. Adding a wall or two usually adds more strength than adding infill. Three or four walls is a common starting point for display pieces that get handled.
- Infill: about 10–20% is a typical starting range for decorative parts. Go higher around screw holes, pegs and mounting points, or use a modifier to add strength just there. Gyroid and similar patterns are popular all-rounders.
- Top and bottom layers: use enough that the infill doesn't show through on the top surfaces.
- Layer height tradeoffs: on a standard 0.4 mm nozzle, around 0.2 mm is the usual default. Go thinner, like 0.12–0.16 mm, for smoother curves on visible surfaces at the cost of time. Go thicker, like 0.24–0.28 mm, for speed on hidden or internal parts. Adaptive or variable layer height can give you both on one print.
Bed adhesion: brims and rafts
Keep it stuck down
- Clean the bed. Fingerprint oil is the most common reason prints don't stick. Clean the plate the way its maker recommends.
- Brim: a few flat lines around the base that add grip and help stop corner lift on big footprints and tall parts. It's easy to trim off.
- Raft: a thick base under the whole part. It's mainly useful for tiny contact areas or a warped bed, and it leaves a rougher bottom.
- Warping materials like ASA (and PETG on large parts) benefit from a brim, a stable room temperature and an enclosure where the material calls for one.
Splitting and joining large models
When it won't fit the bed
- Cut along natural lines, like a seam, an edge or an area that gets painted, so the joint is easy to hide.
- Add alignment keys. Most slicers can add dowels or pins when you cut a model. Leave a small clearance so they fit without forcing.
- Print the parts the same way, with the same settings and filament, so the color and surface match.
- Join them with an adhesive suited to your plastic, such as CA (super) glue for a quick tack or two-part epoxy for strength and gap filling. Check the glue's label for your material.
- Clamp or tape the parts while the glue cures, then fill, sand and prime over the seam. See sanding and priming.
Materials for large skull replicas
PLA, PLA+, PETG, ASA
These are general tradeoffs. Formulas vary by brand, so check your spool's recommended temperatures.
| Material | Good at | Watch out for |
|---|---|---|
| PLA | The easiest to print, with crisp detail and low warping. It sands and paints well. A good default for indoor display pieces. | It softens in heat, like a hot car or a sunny window, and it's more brittle than the others. |
| PLA+ | Usually a bit tougher and less brittle than plain PLA, and still easy to print. | "PLA+" means different things from brand to brand. Heat resistance is still about PLA level. |
| PETG | Tougher and more heat-resistant than PLA, with good layer bonding. | It strings more, can stick too hard to some beds and is harder to sand smooth. |
| ASA | Holds up well to UV and heat, so it's good for outdoor pieces or pieces near a window. | It warps, needs an enclosure and gives off fumes while printing. Ventilate well. |
Note: Print in a ventilated space, especially with ASA. Follow the filament maker's temperature and safety guidance.
Ready for a custom piece?
Send me photos
Every antler is different, so every quote is custom. Send photos through a request form and I'll get back to you.
Dan the 3D Man