Support my work on Patreon

Home / Antler mounting

Guides · Antler mounting

Antler mounting: replica antlers vs. real antlers

There are two different ways antlers go on a BAS (Bullet Anchor Skull), and they don't work the same. Ordering a custom replica? You don't need to drill anything. Replica antlers ship with my proprietary bullet anchor mounting system already attached, so they just plug into the skull. The drilling and screw steps on this page are only for mounting your own real antlers on a BAS skull.

Part 1 · Custom replica orders

Replica antlers: plug-and-play, no drilling

The anchors are already on

No drilling, no screws, no assembly required. Your replica antlers come with my proprietary BAS bullet anchor mounting system already attached. Skip the drilling, screw and epoxy steps further down this page. Those are only for real antlers.

Replica antlers go into the skull the same way real antlers do once their anchors are on. The difference is that I've already done that part for you, so all you do is insert them.

  1. Unpack everything Take the skull and both antlers out of the box.
  2. Insert each antler Push each antler's bullet anchor into its matching socket on the skull.
  3. Clock it to the right angle The anchors can be clocked (turned) in the socket. If an antler's angle looks off, pull it out, turn it and reinsert it until it sits right.
  4. Hang it or display it That's it. It's ready to hang on the wall or set on a desk.

Part 2 · BAS skulls used by themselves

Real antlers on a BAS skull: drilling required

For mounting your own real antlers

This part is only for mounting real deer antlers on a BAS skull you printed or bought by itself. Real antlers don't come with anchors, so you drill a pilot hole in each antler base and attach the bullet anchors with wood screws before pressing them into the skull. Ordered a replica? Skip this part.

Real antlers: before you start

Tools, terms and safety

What "bullet anchors" are: on my BAS (Bullet Anchor Skull) mounts, the bullet anchors are printed anchors that screw onto the base of each antler and press into a matching socket on the printed skull. My published instructions go like this: drill the antlers with a 1/8" bit, attach the bullet anchors with #8 wood screws, then press them into the mating feature on the skull. If an antler is clocked wrong, you can pull it out and reposition it.

Check your design: screw sizes and lengths can differ between skulls. My “Southern” Whitetail instructions call for 2× #8 × 2" (minimum) wood screws. For any other skull, follow the instructions on its MakerWorld page, and use epoxy only if you want the mount permanent.

You'll need

  • The printed skull and its bullet anchors.
  • A drill, a 1/8" bit and #8 wood screws.
  • Optional: slow-setting two-part epoxy.
  • Tape measure and painter's tape.
  • Filler, sandpaper and paint for the burr.

Safety

  • Wear a dust mask and eye protection when drilling or sanding antler.
  • Wear nitrile gloves for epoxy, and work with good ventilation.
  • Clamp the antler. Never hand-hold it while drilling.
  • Follow the labels on your epoxy and filler.

Real antlers, step 1: drilling the antler bases

Centered and straight

  • Dry-fit each antler and mark the front of each base.
  • Mark the center of the base.
  • Clamp it and drill a straight 1/8" pilot hole, a little deeper than the screw.
  • Blow out the dust.
  • Screw the bullet anchor on snug, but don't overtighten it.

Real antlers, step 2: choosing and mixing epoxy (optional)

Only if you want it permanent

  • It's optional. The anchors screw on and press in, so they can be repositioned.
  • Use it for a permanent bond, or to fill a gap at an uneven base.
  • Pick a slow-setting two-part epoxy, and mix it exactly as the label says.
  • Apply a thin layer, wipe off the squeeze-out, and let it cure fully.

Real antlers, step 3: alignment and spread matching

Match the original

  • Measure the inside spread and tip-to-tip from your photos or the original mount.
  • Press both anchors in. If one is clocked wrong, pull it out and turn it.
  • Check the spread, height and angle from the front, top and sides.
  • If you glued it, hold the spread with tape or a spacer until it's fully cured.

Real antlers, step 4: finishing the seam

Make the joint disappear

  • For a permanent mount, fill the gap at the burr with epoxy putty.
  • Sand it smooth with a dust mask on.
  • Prime, then paint the burr to blend it in.
  • Seal it to match the rest of the piece.

More painting and hanging tips are in the how-to guides.

Ready for a custom piece?

Send me photos

Every antler is different, so every quote is custom. Send photos through a request form and I'll get back to you.